Reminder that all parts are sold AS-IS. Shipping is not included in the below prices.

Used flyball governor flyweight / flyball.  Used.  As-Is.

Flyball governor compression spring.  Used.  As-Is.

Flyball governor torsion spring.  Used.  As-Is.

Speed adjusting rod for Jacobs flyball governor.  Used, As-Is.

Flyball governor blade shaft.  Used.  As-Is

Blade shoe for flyball governor blade.  Used.  As-Is.

Sector gear for Jacobs flyball governor.  Used.  As-Is.

Flyball governor central spider gear, cast iron.  Used.  As-is.

Central nut for flyball governor spider gear.  Used.  As-Is.

Generator shaft / hub nut for the flyball governor w/stud for securing nosecone.  Used.  As-Is.

Bolt-on  balance weight for the flyball governor.  Several sizes available.  Used.  As-Is.

Front cover / nosecone for Jacobs flyball governor.  Used.  As-Is.

Rear cover for Jacobs flyball governor.  Used.  Fair condition.  As-Is.

Outer shaft bearing retaining / adjusting nut for Jacobs flyball governor.  Used, As-Is.

Complete flyball governor.  Used.  As-Is.  Includes nosecone and rear cover.

Used original blade set for Jacobs flyball governor.  Includes blade shoes.  May not be a "matched" set.  Fair condition.  Used.  As-Is.

Jacobs 32 volt Model 60 generator only.  Long-Case.  2500 Watt.  Bench / dyno tested and verified to be functional. Used.  As-Is.  Will require local pick-up or truck freight shipping.

Jacobs 32 volt Model 45 generator only.  Short-Case. 1800 Watt.  Bench / dyno tested and verified to be functional.  Used. As-is.  Will require local pick-up or truck freight shipping.

Complete Jacobs tail vane with "whale tail" fin.  Used, As-Is.  9 foot and 10 foot versions available.  Local pick-up or truck freight shipping required.

Complete Jacobs tail vane with "lemon" fin.  Used, As-Is.  8 foot and 9 foot versions available.  Local pick-up or truck freight shipping required.

Tail pull out spring.  New.  E-coated

Tail spring hook.  Generator side.  Used.  As-Is.

Tail hinge pin.  Fitts both top and bottom locations.  Used.  As-Is.

Tail stop chain with spring and mounting castings.  Used.  As-Is.

Tail pull-in chain pulley.  Mounts to the side of generator.  Used.  As-Is.

Tail hoop pulley.  Used.  As-Is.  New also available.

New blade activated governor for both long or short case Jacobs.  Complete.  Includes new blade shoes, new knuckles, new springs and new center ring.   Built to order.

Jacobs blade activated governor springs.  Set of 3.  New. E-Coated

Jacobs blade activated governor springs center ring.  New.

Jacobs blade activated governor spider to blade shoe knuckles.  Set of 3.  New.

Jacobs blade activated governor Blade shoe. New bushings installed but REQUIRES MACHINING to fit your blade shafts.  New.

Jacobs blade activated governor blade shoe bushings. Set of 9.  New. Un-machined.

Jacobs blade activated governor generator shaft hub nut and Lock washer.  New.

Brand new set of 3 Sitka Spruce blades for the blade activated governor.  Unfinished / not painted.  Will require balancing to governor.  New.

Lubriplate Low Temperature synthetic grease.  Recommended for cold climates.  Standard grease gun tube.

Mobil SHC 32 Synthetic grease.  Recommended for warm climates.  Standard grease gun tube.

Complete set of generator brushes.  3 "soft" and 1 "hard" brushes.  For both short-case and long-case generators.  Does NOT fit earlier 1500 watt models.  New.

Generator brush holder including spring.  Used.  As-is.

Complete generator brush rig assembly.  Includes 4 brush holders, cast aluminum housing clamp and jumper bars.  Used.  As-is.

Generator radio filter / condenser / capacitor.  Tested to be functional.  Used.  As-is.

Generator bearings.  New.  Set of 2.  For both upwind and downwind locations.

Upwind generator bearing retaining cap.  Used.  As-is.

Downwind generator bearing retaining cap.  Used.  As-is.

Generator front endbell cover.  Used. Fair condition.  As-Is.

Generator rear endbell cover.  Used. Fair condition.  As-Is.

Upper Tower top casting for 4 leg tower. Used. As-is.  New also available.

 Lower tower casting for 4 leg tower. Used. As-is.  New also available.

Upper Tower top casting for 3 leg tower. Used. As-is.  New also available.

 Lower tower casting for 3 leg tower. Used. As-is.  New also available.

Generator mounting saddle and yaw shaft.  For Jacobs long-case generator only.  Used.  As-Is.

Generator mounting saddle and yaw shaft.  For Jacobs short-case generator only.  Used.  As-Is.

Generator mounting saddle and yaw shaft upper yaw bearing assembly.  Used.  As-Is.

Generator mounting saddle and yaw shaft lower bronze bushing.  New.  REQUIRES MACHINING

Cast iron weatherproof ring for lower yaw shaft.  Used, As-Is.

Cast iron "U" casting.  Used for holding slipring brush card and providing protection from the weather for the sliprings.  Used, As-Is.

Yaw Slipring assembly.  Used.  As-Is.

Yaw Slipring assembly.  New.  Built to order.  Price is for standard set of 3 rings.  We can custom build these with additional rings upon request.

Upgrade slipring brush.  100 Amp rated, dual brush.  Will require slight modification to lower tower yaw casting and removal of "U"- casting.  New.  

New 7 foot stub tower to mount a 1800W or 2500W Jake on a Rohn SSV freestanding tower.  Includes upgraded lower yaw bearing.  New. As-is.  Will require local pick up or truck freight shipping.

Complete used long-case model 60, 32 volt Jacobs.  ALL USED COMPONENTS.  AS -IS.  Includes generator, tail, saddle tube, sliprings, slipring brushes, upper and lower tower castings, blades, and flyball governor.  Generator bench / dyno tested and verified to be functional.  Local pick-up or truck freight shipping required.

Complete used short-case model 45, 32 volt Jacobs.  ALL USED COMPONENTS.  AS -IS.  Includes generator, tail, saddle tube, sliprings, slipring brushes, upper and lower tower castings, blades, and flyball governor.  Generator bench / dyno tested and verified to be functional.  Local pick-up or truck freight shipping required.

Complete original Jacobs control box, 32V, untested.  Price based on overall condition.  Please email for pics and price.  Used. As-is

Monster blocking diode used for customer-built control boxes.  Used. As-is.